Resurrection of the Viking III

After sitting silently in the basement for the past 15 years, the Viking III has risen once again and now resides happily in the more comfortable upstairs station. Back in 1975 I rescued this transmitter, a stock E.F. Johnson Viking I, from the loft of a barn down in southern Connecticut. The owner explained to me that he had assembled it back in the early 50's and stated that he was fairly terrified of it by the time he got around to powering it up for the first time. Unfortunately, after hitting the plate switch, there was a spectacular arc in the tank circuit as he attempted to tune it up for the first time, and the fuse blew. He yanked the power cord from the wall and walked away from it, vowing to never touch it again. So, there it sat for roughly 20 years, until he offered it to me for 35 bucks. After cleaning the hay and mouse turds out of the chassis, I found the cause of the arcing incident to be a bent plate on the tuning cap in the tank circuit. After straightening that out, I fired the rig up and it came to life nicely. As time went on, and my meager supply of 4D32 tubes would no longer pull grid current on the upper bands, I installed 3 x 6146's (hence the nickname Viking III) in the final and mated the RF deck up with an external modulator using a pair of 811's. I ended up putting the whole thing, including the VF-122 VFO, into a six foot rack. It served me well in the basement station for many years until it eventually was neglected as I finished up my 4-400 rig.
1
The old Viking sat dormant for 15 years, which is probably the worst thing you can do to any piece of electronic gear. Last winter, I began thinking about rebuilding the Viking and installing it in the more civilized upstairs station. So, I broke it down and grabbed an empty 3 foot rack from my basement storage and began re-building it. The RF deck needed a good cleaning, some new electrolytics for the LV and bias supplies, and a new power cord with a 3 pronged connector. It powered up fine and made a healthy amount of RF. On the list of things left to do is to rip out the unused remnants of the harness, replace the micamold loading caps with doorknobs, and add a better neutralizing circuit.

2
The RF Deck with 3 x 6146's in the final


3
The bottom components with lots of unused wiring still in the harness to clean out.


V3
New screen resistor, new electrolytics, unused tube sockets and wiring cleaned out. Good to go!


3
Rewiring the modulator deck, which has its own 1500 volt plate supply.


5
Adding in the relays and control circuitry before mounting the Thordarson CHT 300.


6
Up and running comfortably with 150 watts output.
The rig runs very cleanly from 1 watt to over 150 watts output. It actually has been pushed as high as 175 watts out, but I figure the old micamold loading caps are stressed plenty at the 150 watt output level. The variac in the middle panel controls the Viking RF deck's 750 VDC plate supply as well as the modulator's 1500 VDC plate supply. At all power levels, the 811's in the modulator (which sits under the bench) are running at roughly twice the voltage of the three 6146's in the RF deck. The low level audio is generated on one of the station computers, and equalized with software called Voice Shaper which also brickwalls the audio at about 6 kc. That's a good thing, as the modulator appears to pass audio out to about 15 kc, which doesn't make for very neighborly operating on a crowded band (15 kc  + 15 kc = 30 kc). The output of the soundcard is routed through a JBL 7110 compressor/limiter and then fed into a 40 watt solid state audio amp that drives the 8 ohm tap of a backward connected push-pull 6L6 type audio output transformer, with the transformer primary connected to the 811 grids. The receiver is an old Yaesu FRG-7700 which sounds very nice in the 12 kc bandpass position. A more vintage NC-88 is used for casual shortwave and broadcast band listening.

On my very first QSO with the resurrected Viking III it was my fortune to be received by Bill, KC2IFR, who was making a few recordings up and down the band. He emailed me a sound clip so I could hear how the rig sounded. There's still a lot left to finish up, but it's been fun playing with the old Viking III on the air once again!
First contact running about 30 watts with the resurrected Viking III on 75 Meters
During a casual conversation one afternoon with Tim - WA1HLR he suggested that I reconfigure the primary to secondary ratio of the Thordarson CHT-300 modulation transformer. The original 1.73:1 ratio was appropriate for the old 4D32, which pulled 200 ma of plate current, but the three 6146B's typically pull over 300 ma of current and present a much lower tank circuit impedance. Tim determined that a ratio of 2.32:1 would allow the 811'As to develop much more audio, so I rewired the primary and secondary taps as he instructed me to. The end result of that was much smoother and louder audio with about half the amount of audio drive power. The clip below was captured by Eric - WB2CAU on his Flex 5000.



Thanks Eric for the EQ suggestions! Thank you Tim, for pulling the Thordarson CHT-300 tap connections out of your head! I am always amazed by the vast repository of technical information that he has acquired and retained through his experience over the years. Even more impressive is his willingness to share it with others.